- 您现在的位置：买卖IC网 > Sheet目录368 > W25Q80BWSSIG (Winbond Electronics)IC FLASH SPI 8MBIT 8SOIC
W25Q80BW
7.2.30
Release Power-down / Device ID (ABh)
The Release from Power-down / Device ID instruction is a multi-purpose instruction. It can be used to
release the device from the power-down state, or obtain the devices electronic identification (ID) number.
To release the device from the power-down state, the instruction is issued by driving the /CS pin low,
shifti ng the instruction code “ABh” and driving /CS high as shown in figure 28a. Release from power-
down will take the time duration of t RES1 (See AC Characteristics) before the device will resume normal
operation and other instructions are accepted. The /CS pin must remain high during the t RES1 time
duration.
When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by
driving the /CS pin low and shifting the instruction code “ABh” followed by 3 -dummy bytes. The Device ID
bits are then shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in figure
28a. The Device ID values for the W25Q80BW is listed in Manufacturer and Device Identification table.
The Device ID can be read continuously. The instruction is completed by driving /CS high.
When used to release the device from the power-down state and obtain the Device ID, the instruction is
the same as previously described, and shown in figure 28b, except that after /CS is driven high it must
remain high for a time duration of t RES2 (See AC Characteristics). After this time duration the device will
resume normal operation and other instructions will be accepted. If the Release from Power-down /
Device ID instruction is issued while an Erase, Program or Write cycle is in process (when BUSY equals
1) the instruction is ignored and will not have any effects on the current cycle.
/CS
tRES1
Mode 3
0
1
2
3
4
5
6
7
Mode 3
CLK
Mode 0
Mode 0
Instruction (ABh)
DI
(IO 0 )
Power-down current
Figure 28a. Release Power-down Instruction Sequence
- 48 -
Stand-by current
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
W25X40BVZPIG
IC SPI FLASH 4MBIT 8WSON
W25X64VZEIG
IC FLASH 64MBIT 75MHZ 8WSON
W25X80AVDAIZ
IC FLASH 16MBIT 100MHZ 8DIP
W29GL032CB7A
IC FLASH 32MBIT 70NS 48TFBGA
W29GL064CB7S
IC FLASH 64MBIT 70NS 48TSOP
W29GL128CL9T
IC FLASH 128MBIT 90NS 56TSOP
W631GG6KB-15
IC DDR3 SDRAM 1GBIT 96WBGA
W9412G6IH-5
IC DDR-400 SDRAM 128MB 66TSSOPII
相关代理商/技术参数
W25Q80BWSSIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q80BWUXIG
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q80BWUXIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q80BWZPIG
功能描述:IC FLASH SPI 8MBIT 8WSON RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR)
W25Q80BWZPIG TR
功能描述:IC FLASH SPI 8MBIT 8WSON RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,000 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 异步 存储容量:256K (32K x 8) 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:28-TSSOP（0.465"，11.8mm 宽） 供应商设备封装:28-TSOP 包装:带卷 (TR) 其它名称:71V256SA15PZGI8
W25Q80BWZPIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25S243A
制造商:WINBOND 制造商全称:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM
W25S243A-12
制造商:WINBOND 制造商全称:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM